4-249-164-11(1)
Micro Hi-Fi
Component
System
Operating Instructions
CMT-SE1
©2003 Sony Corporation
Table of Contents
Listening to audio from a connected
component...................................... 15
Recording on a connected
component...................................... 15
Using the Radio Data System
(RDS)..............................................10
Viewing information about the disc in the
display.............................................13
3GB
Getting Started
Hooking up the system
Perform the following procedures 1 to 3 to hook up your system using the supplied cords and
accessories.
AM loop antenna
FM lead antenna
Right speaker
Left speaker
1
2
3
1 Connect the speakers.
Connect the right and left speaker cords to
the SPEAKER terminals as shown below.
L
IA
X
A
O
C
M
A
Ω
4
SE
L
U
E
C
M
F
AN
PED
AM loop antenna
Ω
IM
75
R
R
AKE
Extend the FM lead antenna horizontally
PE
S
Note
To prevent noise pickup, keep the antennas away from
the system and other components.
2 Connect the FM and AM antennas.
Set up the AM loop antenna, then connect
it.
3 Connect the mains lead to mains.
If the plug does not fit the wall socket,
detach the supplied plug adaptor (only for
models equipped with an adaptor).
To turn on the system, press ?/1.
4GB
Attaching the speaker pads
Setting the clock
Attach the supplied speaker pads to the bottom
of the speakers to stabilize the speakers and
prevent them from slipping.
1
2
3
Press ?/1 to turn on the system.
Press CLOCK/TIMER SET.
Press . or > repeatedly to set the
hour.
4
5
Press ENTER.
Press . or > repeatedly to set the
minute.
6
Press ENTER.
The clock starts working.
Inserting two R6 (size AA)
batteries into the remote
To adjust the clock
1 Press CLOCK/TIMER SET.
2 Press . or > until “CLOCK SET?”
appears, then press ENTER.
3 Do the same procedures as step 3 to 6
above.
e
Note
E
E
The clock is not displayed in Power Saving Mode.
e
Tip
When you adjust the clock while the system is off, do
Note
the same procedures as step 2 to 6 above.
If you do not use the remote for a long period of time,
remove the batteries to avoid possible damage from
battery leakage and corrosion.
Tip
When the remote no longer operates the system,
replace both batteries with new ones.
Opening the front cover
Pull down the upper right corner of the front
cover on the unit.
Front cover
5GB
Playing a disc
— Normal Play/Shuffle Play
CD – Play
Loading a disc
This system lets you play CD in different play
modes.
1
Press CD (or FUNCTION on the unit
repeatedly) to switch the function to
CD.
2
Insert a disc in the disc slot with the
label side up.
Track number
Playing time
1
2
Press CD (or FUNCTION on the unit
repeatedly) to switch the function to
CD.
Whenyouplay
a disc, insert it
with the label
side up.
Press PLAY MODE in stop mode
repeatedly until the mode you want
appears.
Select
To play
No display
(Normal Play)
The tracks on the disc in
original order.
Notes
• When you turn on the system, the disc is not pulled
into the disc slot until “CD No Disc” appears in the
display. Do not attempt to push in the disc until “CD
No Disc” appears.
SHUFFLE
(Shuffle Play)
All tracks on the disc in
random order.
PROGRAM
(Program Play)
The tracks on the disc in the
order you want them to be
played (see “Creating your
• Do not use a disc with tape, seals or paste on it as this
may cause malfunction.
3
Press N.
Other operations
To
Do this
Stop play
Pause
Press x.
Press X. Press again to resume
play.
Select a track
Press . or > repeatedly.
Find a point in a Keep pressing m or M during
track
playback and release it at the
desired point.
Remove a disc
Press Z EJECT on the unit.
Note
You cannot change the play mode during playback.
Tip
When disc access takes a long time, set “CD PowerOn”
6GB
Playing repeatedly
— Repeat Play
Creating your own
program
— Program Play
You can play all the tracks or a single track on a
disc repeatedly.
You can make a program of up to 25 steps.
Press REPEAT repeatedly during playback
until “REPEAT” or “REPEAT 1” appears.
1
Press CD (or FUNCTION on the unit
repeatedly) to switch the function to
CD.
REPEAT: For all the tracks on the disc up to five
times.
2
3
Press PLAY MODE in stop mode
repeatedly until “PROGRAM” appears.
REPEAT 1: For a single track only.
To cancel Repeat Play
Press REPEAT repeatedly until both
“REPEAT” and “REPEAT 1” disappear.
Press . or > repeatedly until the
desired track number appears.
Note
When you select “REPEAT 1”, that track is repeated
endlessly until “REPEAT 1” is canceled.
Selected track number Total playing time
4
Press ENTER.
The track is programmed.
The step number appears, followed by the
last programmed track number.
5
6
To program additional tracks, repeat
steps 3 and 4.
Press N.
Program Play starts.
Other operations
To
Do this
Cancel Program Play Press PLAY MODE in stop
mode repeatedly until
“PROGRAM” disappears.
Clear a track from the Press CLEAR in stop mode.
end
Add a track to the end Perform steps 3 and 4 in stop
of the program
mode.
Tips
• The program you made remains after Program Play
finishes. To play the same program again, press N.
However, the program is cleared when you eject the
disc.
• “– –.– –” appears when the total program time
exceeds 100 minutes, or when you select a CD track
numbered 21 or over.
7GB
5
Press PRESET +/– repeatedly to select
the desired preset number.
Tuner
6
7
Press ENTER.
Presetting radio stations
Repeat steps 1 through 6 to preset
other stations.
You can preset up to 20 FM stations and 10 AM
stations. You can then tune in any of those
stations simply by selecting the corresponding
preset number.
Tip
Press TUNING MODE to stop scanning.
Manual tuning preset
You can manually tune in and store the radio
frequency of the desired stations.
Automatic tuning preset
You can automatically tune in all of the stations
that can be received in your area and then store
the radio frequency of the desired stations.
1
2
3
Press TUNER/BAND repeatedly (or
move lever on the unit to FM or AM) to
select “FM” or “AM”.
1
Press TUNER/BAND repeatedly (or
move lever on the unit to FM or AM) to
select “FM” or “AM”.
Press TUNING MODE repeatedly until
both “AUTO” and “PRESET” disappear
from the display.
2
3
Press TUNING MODE repeatedly until
“AUTO” appears in the display.
Press TUNING +/– repeatedly to tune in
the desired station.
Press TUNING +/–.
4
5
Press TUNER MEMORY.
The frequency changes as the system scans
for a station. Scanning stops automatically
when a station is tuned in. At that time,
“TUNED” and “STEREO” (for stereo
program only) appear.
Press PRESET +/– repeatedly to select
the desired preset number.
6
7
Press ENTER.
Repeat steps 1 through 6 to preset
other stations.
If “TUNED” does not appear and the
scanning does not stop
Other operations
Set the frequency of the desired radio
station as described in steps 2 and 3 of
To
Do this
Tune in a station
Follow the procedure described
4
Press TUNER MEMORY.
The preset number flashes. Perform steps 5
and 6 while the preset number flashes.
Set another station After step 4, press PRESET +/–
to the existing
preset number
repeatedly to select the preset
number you want to store the
station.
Tips
Preset number
• The preset stations are retained for about half a day
even if you disconnect the mains lead or if a power
failure occurs.
• To improve the reception, adjust the supplied
antennas or connect an external antenna.
8GB
To improve tuner reception
When tuner reception is poor, set CD player
power off by CD power manage function.
CD power is factory set to on.
Listening to the radio
You can listen to a radio station either by
selecting a preset station, or by manually tuning
in the station.
1 Press CD (or FUNCTION on the unit
repeatedly) to switch the function to CD.
2 Press ?/1 to turn off the system.
Listening to a preset station
3 Press ?/1 while holding x.
“CD PowerOff” appears.
— Preset Tuning
To set CD power on
Repeat the procedure above and “CD PowerOn”
appears.
Preset radio stations in the tuner’s memory first
1
Press TUNER/BAND repeatedly (or
move lever on the unit to FM or AM) to
select “FM” or “AM”.
Notes
• When “CD PowerOff” is selected, disc access time is
increased.
2
3
Press TUNING MODE repeatedly until
“PRESET” appears in the display.
• You cannot change the setting in Power Saving
Mode.
Press PRESET +/– repeatedly to select
the desired preset station.
Listening to non-preset radio
station
— Manual Tuning
1
2
Press TUNER/BAND repeatedly (or
move lever on the unit to FM or AM) to
select “FM” or “AM”.
Press TUNING MODE repeatedly until
both “AUTO” and “PRESET” disappear
from the display.
3
Press TUNING +/– repeatedly to tune in
the desired station.
Tips
• To improve broadcast reception, adjust the supplied
antennas, or connect a commercially available
external antenna.
• When an FM stereo program has static noise, press
FM MODE repeatedly until “MONO” appears.
There will be no stereo effect, but the reception will
improve.
• Press TUNING MODE repeatedly until “AUTO”
appears in step 2 above, then press TUNING +/–.
The frequency indication changes and scanning stops
automatically when the system tunes in a station
(Automatic Tuning).
9GB
Using the Radio Data
System (RDS)
What is the Radio Data
System?
Radio Data System (RDS) is a broadcasting
service that allows radio stations to send
additional information along with the regular
program signal. RDS is available only on FM
stations.*
Note
RDS may not work properly if the station you are tuned
in is not transmitting the RDS signal properly or if the
signal is weak.
* Not all FM stations provide RDS service, nor do they
provide the same types of services. If you are not
familiar with the RDS system, check with your local
radio stations for details on RDS services in your
area.
Receiving RDS broadcasts
Simply select a station from the FM band.
When you tune in a station that provides RDS
services, the station name appears in the display.
To check the RDS information
Each time you press DISPLAY, the display
changes cyclically as follows:
Station name* t Frequency t Clock display
t Bass level t Treble level
* If the RDS broadcast is not properly received, the
station name may not appear in the display.
10GB
Sound Adjustment
Timer
Adjusting the sound
Falling asleep to music
— Sleep Timer
You can adjust the bass and treble to enjoy more
powerful sound.
You can set the system to turn off after a certain
time, so that you can fall asleep to music.
Generating a more dynamic
sound (Dynamic Bass Feed
Back)
Press SLEEP.
Each time you press the button, the minute
display (the turn-off time) changes cyclically as
follows:
AUTO* t 90min t 80min t … t 10min
t OFF
DBFB is factory set to on.
To cancel the DBFB, press DBFB.
* The system automatically turns off in 240 minutes or
after the current CD finishes playing.
Adjusting the bass and treble
Other operations
You can adjust the bass and treble.
To
Do this
Press BASS +/– or TREBLE +/– repeatedly
to adjust the level you want to set.
Check the
remaining time**
Press SLEEP once.
To adjust the bass and treble on
the unit
Change the time to Press SLEEP repeatedly to select
turn off the time you want.
Cancel the Sleep Press SLEEP repeatedly until
Timer Function “OFF” appears.
1 Press BASS/TREBLE on the unit repeatedly
to select “BASS” or “TREBLE”.
Each time you press the button, the display
changes as follows:
**You cannot check the remaining time if you select
“AUTO”.
BASS y TREBLE
Tip
2 Press +/– on the unit repeatedly to adjust the
level while “BASS” or “TREBLE” appears.
You can use the Sleep Timer, even if you have not set
the clock.
To exit the bass and treble
settings
Press any button other than BASS +/–, TREBLE
+/–, BASS/TREBLE on the unit or +/– on the
unit.
Also, if you do not perform any operations for a
few seconds, the display automatically returns to
the original display.
11GB
Other operations
Waking up to music
— Daily Timer
To
Do this
Check the setting
1 Press CLOCK/TIMER
SELECT.
2 Press . or >
repeatedly until “DAILY
ON?” appears, then press
ENTER.
You can wake up to music at a preset time. Make
sure you have set the clock (see “Setting the
1
Prepare the sound source you want to
play.
Change the setting Start over from step 1.
Cancel the timer
1 Press CLOCK/TIMER
SELECT.
• CD: Insert a disc. To start from a specific
track, make a program (see “Creating
2 Press . or >
repeatedly until “DAILY
OFF?” appears, then press
ENTER.
• TUNER: Tune in the preset radio station
2
Press VOL +/– (or turn VOLUME control
on the unit) to adjust the volume.
Notes
• If you use the Daily Timer and the Sleep Timer at the
same time, the Sleep Timer has priority.
• If the system is on about 15 seconds before the preset
time, the Daily Timer will not be activated.
• You cannot use the optional component connected to
MD (TAPE) IN jack as the sound source for Daily
Timer.
3
4
Press CLOCK/TIMER SET.
Press . or > repeatedly until
“DAILY SET ?” appears, then press
ENTER.
5
Set the time to start playing.
Press . or > repeatedly to set the
hour, then press ENTER.
The minute indication flashes.
Press . or > repeatedly to set the
minute, then press ENTER.
6
7
Set the time to stop playing following
the same procedure as step 5.
Press . or > repeatedly until the
desired sound source appears.
Each time you press the button, the display
changes cyclically as follows:
TUNER y CD PLAY
8
9
Press ENTER.
The start time, the stop time, the sound
source and the volume appear in turn, then
the original display returns.
Press ?/1 to turn off the system.
12GB
Viewing information
about the disc in the
display
Display
Turning off the display
— Power Saving Mode
You can check the playing time and remaining
time of the current track or that of the disc.
The clock display can be turned off to minimize
the amount of power consumed during standby
(Power Saving Mode).
Checking the remaining time
and titles (CD)
Press DISPLAY repeatedly while the
system is off until the clock display
disappears.
Press DISPLAY during Normal Play.
Each time you press the button, the display
changes cyclically as follows:
To cancel Power Saving Mode
Press DISPLAY while the system is off. Each
time you press the button, the display switches
cyclically as follows:
Clock display* y No display (Power Saving
Mode)
Current track number and elapsed playing time
t Current track number and remaining time t
Remaining time of the disc*1 t Track title of
CD-TEXT disc*2 t Clock display t
Bass level t Treble level
* The clock is displayed only if you set the clock.
*1
“– –.– –” appears in Program Play mode.
*2
Note
When the disc contains more than 20 tracks,
You cannot perform the following operations in Power
CD-TEXT is not displayed from track 21 on.
Saving Mode.
– setting the clock
Checking the total playing
time and titles (CD)
– changing the CD power manage function
– switching the MD (TAPE) function
Tips
Press DISPLAY in stop mode.
• ?/1 indicator lights up even in Power Saving Mode.
• The timer continues to operate in Power Saving
Mode.
Each time you press the button, the display
changes cyclically as follows:
Total playing time t Disc title* t
Clock display t Bass level t Treble level
* For CD-TEXT discs (certain characters cannot be
displayed).
Note
When fast forward or fast reverse is performed, elapsed
playing time and remaining time of the track may not
be displayed accurately.
13GB
Optional Components
Hooking up optional components
To enhance your system, you can connect optional components. Refer to the operating instructions
provided with each component.
Optional digital component
Optional analog component
To the digital
To the audio
input jack of an
optional analog
component
From the audio
output jack of an
optional analog
component
input jack of an
optional digital
component
A MD (TAPE) IN jack (stereo mini
jack)
C CD OPTICAL OUT DIGITAL
jack
Use audio cord (not supplied) to connect an
optional analog component (MD deck or tape
deck, etc.) to this jack. You can then listen to the
sound from the component.
Use a digital optical cable (square, not supplied)
to connect an amplifier, MD deck, or DAT deck
with a digital optical input jack. Digital signal is
output only when the system function is set to
CD. If the jack is covered with a cap, remove it
before use.
B MD (TAPE) OUT jack (stereo
mini jack)
Use audio cord (not supplied) to connect an
optional analog component (MD deck or tape
deck, etc.) to this jack. You can then listen to the
sound through this system.
14GB
Listening to audio from a
connected component
Recording on a connected
component
Listening to a connected MD
deck
Making an analog recording
1
Connect the audio cord.
1
Connect the audio cord.
2
Start recording.
2
Press MD (TAPE) (or FUNCTION on the
unit) repeatedly until “MD” appears.
Refer to the operating instructions provided
with connected component.
Start playing the connected component.
Making a digital recording
Listening to a connected tape
deck
1
2
Connect the digital optical cable.
Start recording.
1
Connect the audio cord.
Refer to the operating instructions provided
with connected component.
Note
2
Press MD (TAPE) (or FUNCTION on the
unit) repeatedly until “TAPE” appears.
You can digitally record from the discs only. However,
you cannot record from copy prohibited discs.
Hold down FUNCTION on the unit and
press ?/1 on the unit. This switches the
MD function to TAPE. Once you enable the
TAPE function, just press MD (TAPE).
Tip
If you cannot select “MD” by pressing MD (TAPE) (or
FUNCTION on the unit) repeatedly, turn off the
system and then press ?/1 on the unit while holding
down FUNCTION on the unit. The function will
change from “TAPE” to “MD”, and “MD” will appear
in the display. To change back to “TAPE”, repeat the
same procedure. However, you cannot switch the MD/
TAPE function in Power Saving Mode.
15GB
General
“– –:– –” appears in the display.
Troubleshooting
• A power interruption has occurred. Set the clock
Problems and remedies
The clock setting/radio presetting/timer is
canceled.
Should you encounter a problem with your
system, do the following:
• Redo the following:
1 Make sure the mains lead and speaker
cords are correctly and firmly connected.
2 Find your problem in the troubleshooting
checklist below and take the indicated
corrective action.
There is no sound.
• Press VOL +/– or turn VOLUME control on the
unit clockwise.
If the problem persists after doing all of the
above, consult your nearest Sony dealer.
• Make sure the headphones are not connected.
Sound comes from one channel, or
unbalanced left and right volume.
• Place the speakers as symmetrically as possible.
• Connect the supplied speakers.
When the ?/1 indicator flashes
Immediately unplug the mains lead and check
the following items.
Sound lacks bass.
• Are the system control cables connected
correctly?
• Check that the speaker’s + and – jacks are
connected correctly.
• If your system has a voltage selector, is the
voltage selector set to the correct voltage?
Check the voltage for your region, then
make sure the voltage selector is set
correctly.
There is severe hum or noise.
• Move the system away from the source of noise.
• Connect the system to a different mains.
• Install a noise filter (commercially available) to
the mains line.
• Are the + and – speaker cords short-
circuited?
The timer cannot be set.
• Are you using the supplied speakers?
• Is anything blocking the ventilation holes
on the rear of the system?
Check all the above items and fix any
problems found. After ?/1 indicator stops
flashing, reconnect the mains lead and turn on
the system. If the indicator still flashes, or if
the cause of the problem cannot be found
even after checking all the above items,
consult your nearest Sony dealer.
The timer does not function.
• Press CLOCK/TIMER SELECT to set the timer
• Check the timer setting and set the correct time
• Make sure the clock is correctly set.
The color on the TV screen is irregular.
• Move the speakers farther away from the TV set.
The remote does not function.
• Remove the obstacle.
• Move the remote closer to the system.
• Point the remote at the system’s sensor.
• Replace the batteries (R6/size AA).
• Locate the system away from the fluorescent light.
16GB
CD
Tuner
“LOCKED” appears.
Severe hum or noise/stations cannot be
received.
• Contact your Sony dealer or local authorized Sony
service facility.
• Find a place and an orientation that provide good
reception, then set up the antenna again. If you
cannot obtain good reception, we recommend you
connect a commercially available external
antenna.
The disc does not eject.
• Consult your nearest Sony dealer.
Play does not start.
• Check whether a disc is loaded (The DISC
indicator lights up when a disc is loaded).
• The supplied FM lead antenna receives signals
along its entire length, so make sure you extend it
fully.
• Replace the disc.
• Load the disc that this system can play.
• Load the disc correctly.
• Keep the antennas away from the system and
other components.
• Load the disc in the player with the label side up.
• Remove the disc and wipe away the moisture on
the disc, then leave the system turned on for a few
hours until the moisture evaporates.
• Press N to start play.
• Consult your nearest Sony dealer if the supplied
AM antenna has come off the plastic stand.
• Try turning off surrounding electrical equipment.
• Set “CD PowerOff” by CD power manage
Disc access takes a long time.
• Set “CD PowerOn” by CD power manage
A stereo FM program cannot be received in
stereo.
• Press FM MODE until “MONO” disappears from
the display.
The sound skips.
• Replace the disc.
• Try moving the system to a place without
vibration (e.g., on top of a stable stand).
• Try moving the speakers away from the system, or
placing them on separate stands. When you listen
to a track with bass sounds at high volume, the
speaker vibration may cause the sound to skip.
Optional components
There is no sound.
(page 16) and check the condition of the system.
checking:
Play does not start from the first track.
• Press PLAY MODE repeatedly until both
“PROGRAM” and “SHUFFLE” disappear to
return to Normal Play.
– if the cords are connected properly.
– if the cord plugs are firmly inserted all the way.
• Turn on the connected component.
• Refer to the operating instructions supplied with
the connected component and start playing.
• Press MD (TAPE) (or FUNCTION on the unit)
The sound is distorted.
• Set the volume of the connected component
lower.
continued
17GB
If the system still does not
operate properly after performing
the above measures, reset the
system as follows:
Messages
One of the following messages may appear or
flash in the display during operation.
1 Disconnect the mains lead.
2 Reconnect the mains lead.
3 Press ?/1 to turn on the system.
CD
No Disc
There is no disc in the player.
4 Move lever on the unit to x and press
FUNCTION and ?/1 on the unit.
No Step
All of the programmed tracks have been erased.
The system is reset to the factory settings. You
should set the settings you made, such as the
preset stations, clock, and timer.
Over
You have reached the end of the disc while pressing
M during playback or pause.
Push STOP!
You pressed PLAY MODE during playback.
Step Full!
You tried to program 25 or more tracks (steps).
TUNER
Complete!
The preset operation ended normally.
TIMER
OFF TIME NG
The Daily Timer start and end times are set to the
same time.
SET CLOCK!
You tried to set the timer, before you set the clock.
SET TIMER!
You pressed CLOCK/TIMER SELECT, before you
set the timer.
18GB
On operation
• If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens inside the CD
player. Should this occur, the system will not operate
properly. Remove the disc and leave the system
turned on for about an hour until the moisture
evaporates.
Additional Information
Precautions
On operating voltage
Before operating the system, check that the operating
voltage of your system is identical with the voltage of
your local power supply.
• When you move the system, take out any disc.
If you have any questions or problems concerning your
system, please consult your nearest Sony dealer.
On safety
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• Unplug the system from the wall outlet (mains) if it
is not to be used for an extended period of time. To
disconnect the power cord (mains lead), pull it out by
the plug. Never pull the cord itself.
Notes on discs
• Before playing, clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzene, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car
parked in direct sunlight.
• Should any solid object or liquid fall into the system,
unplug the system and have it checked by qualified
personnel before operating it any further.
• Do not use discs encircled with a protection ring.
This may cause a malfunction to the system.
• When using discs that have glue or similar tacky
substance on the label side of the disc or that used a
special ink when the label was printed, there is a
chance that the disc or label may become attached to
parts inside this unit. When this occurs, it may not be
possible to remove the disc, and may also cause this
unit to malfunction. Be sure to check that the label
side of the disc is not sticky before using.
• AC power cord (mains lead) must be changed only at
the qualified service shop.
On placement
• Do not place the system in an inclined position.
• Do not place the system in locations where it is;
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
The following types of disc should not be used:
– Rental or used discs with attached seals where the
glue extends beyond the seal. The perimeter of the
seal on the disc is tacky.
– Subject to direct sunlight.
• Use caution when placing the unit or speakers on
surfaces that have been specially treated (with wax,
oil, polish, etc.) as staining or discoloration of the
surface may result.
– Discs that have labels printed using a special ink
that feels tacky when touched.
On heat buildup
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this unit. Attempting to do
so may damage the unit. Do not use such discs.
• Although the system heats up during operation, this
is not a malfunction.
• Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
• If you continuously use this system at a high volume,
the cabinet temperature of the top, side and bottom
rises considerably. To avoid burning yourself, do not
touch the cabinet.
Notes on CD-R and CD-RW
• This system can play CD-R/CD-RW discs edited by
the user. However, note that playback of some discs
may not be possible depending on the recording
device used for recording or the disc condition.
• CD-R and CD-RW discs that have not been finalized
(processing to allow play by a normal CD player)
cannot be played.
• To prevent a malfunction, do not cover the
ventilation hole.
• CD-R and CD-RW discs recorded in multi-session
mode are not supported.
continued
19GB
Music discs encoded with copyright
protection technologies
Specifications
This product is designed to playback discs that
conform to the Compact Disc (CD) standard. Recently,
various music discs encoded with copyright protection
technologies are marketed by some record companies.
Please be aware that among those discs, there are some
that do not conform to the CD standard and may not be
playable by this product.
Main Unit (HCD-SE1)
Amplifier section
DIN power output (rated): 55 + 55 W
(4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
80 + 80 W
Cleaning the cabinet
(4 ohms at 1 kHz, 10%
THD)
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with mild detergent solution. Do not
use any type of abrasive pad, scouring powder or
solvent such as thinner, benzene or alcohol.
Inputs
MD (TAPE) IN (stereo mini jack):
Sensitivity 450/250 mV,
impedance 47 kilohms
Outputs
CD OPTICAL OUT DIGITAL:
Optical Wavelength:
660 nm
PHONES:
Accepts headphones with
an impedance of 8 ohms or
more
MD (TAPE) OUT (stereo mini jack):
Impedance 1 kilohm
SPEAKER:
Accepts impedance of
4 ohms
CD player section
Laser
Semiconductor laser
(CD: λ=780 nm)
Emission duration:
continuous
Frequency response
Wavelength
2 Hz – 20 kHz
780 – 790 nm
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz
(50 kHz step)
Antenna
Antenna terminals
Intermediate frequency
FM wire antenna
75 ohms unbalanced
10.7 MHz
AM tuner section
Tuning range
531 – 1,602 kHz
(9 kHz step)
Antenna
AM loop antenna, external
antenna terminal
450 kHz
Intermediate frequency
20GB
Speaker (SS-SE1)
Speaker system
Speaker units
Woofer:
2-way, bass-reflex type
13 cm dia., cone type
2.5 cm dia., soft-dome-
type
Tweeter:
Nominal impedance
4 ohms
General
Power requirements
Power consumption
230 V AC, 50/60 Hz
45 W
0.3 W (in Power Saving
mode)
Dimensions (w/h/d) incl. projecting parts and controls
Amplifier/Tuner/CD section:
Approx. 155 × 119 ×
289 mm
Speakers:
Approx. 160 × 280 ×
270 mm
Mass
Amplifier/Tuner/CD section:
Approx. 3.0 kg
Speakers:
Approx. 4.0 kg net per
speaker
Supplied accessories
Remote (1)
R6 (size AA) batteries (2)
AM loop antenna (1)
FM lead antenna (1)
Speaker pads (8)
Design and specifications are subject to change
without notice.
21GB
List of button locations and reference pages
How to use this page
Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.
Illustration number
r
R
R
Name of button/part Reference page
Main unit
BUTTON DESCRIPTIONS
ALPHABETICAL ORDER
./> (go back/go forward)
P – Z
A – O
PHONES jack 9
Remote sensor 2
Disc slot 4
Display window 5
Front cover 7
Lever qa qd
?/1
22GB
Remote control
ALPHABETICAL ORDER
BUTTON DESCRIPTIONS
R – Z
A – Q
./> (go back/go forward)
m/M (rewind/fast forward)
CLOCK/TIMER SELECT 2
23GB
Sony Corporation Printed in Korea
|
Sharp MP3 Player DV NC150U User Manual
Smooth Fitness Treadmill 91 SERIES User Manual
Sonic Alert Clock SBH400SS User Manual
Sony Home Theater System 4 147 229 131 User Manual
Sony Speaker System SA VA15 User Manual
Sony Universal Remote RM AX5000 User Manual
Sundance Spas Network Card ST201 User Manual
Sylvania CRT Television SRT2213B SRT2219B User Manual
Tamron Camera Lens AF007N 700 User Manual
Tanaka Chainsaw ECS 351 User Manual